DC to DC Battery Charger - Best Charging Systems (7)

Overview     BCDC1250D Manual The REDARC BCDC1250D In-vehicle Battery Charger is a 12V 50A In-vehicle DC to DC battery charger. It is the latest variant of the award-winning BCDC Dual range and features REDARC’s Smart Start technology. Styled with a red line running down its back tells you there’s something different about this dual battery charger. A 50-amp charging output makes it the most powerful in REDARC’s BCDC range.  The BCDC1250D has been developed to provide a higher current output, it features an additional charging stage known as SoftStart which has been engineered to handle more demanding applications. Featuring a Maximum Power Point Tracking (MPPT) solar regulator, the BCDC1250D will charge from both solar and the alternator simultaneously. And, with built-in 'Green Power Priority' it will select solar charging first, meaning less load on the alternator. Suitable for 12 or 24-volt vehicle systems, the unit will also work with either standard or variable/smart alternators. It is compatible with all common types of batteries used in automotive and recreational vehicles such as AGM, Gel, standard lead acid, Calcium and LiFeP04. As a guide, the BCDC1250D is used for battery bank sizes over 200AH. For smaller batteries of 75-200AH REDARC recommends the BCDC1225D.    Proven and Tested The award-winning technology in the BCDC has been independently verified and tested to ensure battery life is maximised, charging your battery to a proven 100%. Built in Australia and tested for our unique conditions, the DC to DC battery charger will work in the extreme heat of the Simpson Desert, up to 80°C and can handle deep water crossings at Cape York – water, dust and vibration are no match for this charger. If you’re heading out into the bush and want to get there and back again safely – you can trust REDARC.     Features           50amp output makes it the most powerful in REDARC's BCDC range           Separate DC and solar charging inputs           Maximises the performance and life of your auxiliary battery           Simultaneous DC and solar charging with Green Power Priority           Suits 12V/24V standard and variable voltage/smart alternators           Suitable for AGM, GEL, standard lead acid, calcium and LiFeP04 batteries Specifications Input (Operating) Voltage 9 - 32VDC Output System Voltage 12VDC Maximum Charging Voltage 15.3V Output Current Rating (Cont.) 50A Input Fuse Rating 60A Output Fuse Rating 60A Standby Current Draw <100mA Output Power 750W Width (mm) 120 Height (mm) 37 Length (mm) 165 Weight (kg) 1 Warranty 2 Years Videos

When you need to mount your auxiliary battery a distance away from the start battery,  in a caravan, Ute tub, rear of wagon or camper trailer, the voltage drop across a long cable might prevent your auxiliary battery from fully charging and in turn reducing the life of your battery. The REDARC BCDC1240D would be a solution   Proven and Tested The award-winning technology in the BCDC has been independently verified and tested to ensure battery life is maximised, charging your battery to a proven 100%. Built in Australia and tested for our unique conditions, the DC to DC battery charger will work in the extreme heat of the Simpson Desert, up to 80°C and can handle deep water crossings at Cape York – water, dust and vibration are no match for this charger. If you’re heading out into the bush and want to get there and back again safely – you can trust REDARC.   Separate DC and solar charging inputs Maximises the performance and life of your auxiliary battery Simultaneous DC and solar charging with Green Power Priority Suits 12V/24V standard and variable voltage/smart alternators Suitable for AGM, GEL, standard lead acid, calcium and LiFePO4 batteries   SPECIFICATIONS Input (Operating) Voltage 9 - 32VDC Output System Voltage 12VDC Maximum Charging Voltage 15.3V Output Current Rating (Cont.) 40A Type Approval E-Mark Input Fuse Rating 60A Output Fuse Rating 60A Warranty 2 Years Standby Current Draw <100mA Output Power 600W Width (mm) 120 Height (mm) 37 Length (mm) 165 Weight (kg) 1   VIDEOS

Overview     BCDC Dual Manual The REDARC BCDC1225D In-vehicle Battery Charger is the next generation in REDARC's DC to DC charging technology, with additional features that make it the most advanced dual battery charger on the market. Featuring a Maximum Power Point Tracking (MPPT) solar regulator, the BCDC1225D will charge from both solar and the alternator simultaneously. And, with built-in 'Green Power Priority' it will select solar charging first, meaning less load on the alternator. Suitable for 12 or 24-volt vehicle systems, the unit will also work with either standard or variable/smart alternators. The BCDC1225D features the same patented charging profiles as it’s predecessor along with a new lithium charging profile making the unit suitable for charging AGM, Gel, Standard Lead Acid, Calcium and LiFePO4 batteries. For most applications, the BCDC1225D is suitable for battery bank sizes of 75-200AH. For higher capacity needs of over 200AH, REDARC recommends the BCDC1240D.  Proven and Tested The award-winning technology in the BCDC has been independently verified and tested to ensure battery life is maximised, charging your battery to a proven 100%. Built in Australia and tested for our unique conditions, the DC to DC battery charger will work in the extreme heat of the Simpson Desert, up to 80°C and can handle deep water crossings at Cape York – water, dust and vibration are no match for this charger. If you’re heading out into the bush and want to get there and back again safely – you can trust REDARC.     Features Separate DC and solar charging inputs Maximises the performance and life of your auxiliary battery Simultaneous DC and solar charging with Green Power Priority Suits 12V/24V standard and variable voltage/smart alternators Suitable for AGM, GEL, standard lead acid, calcium and LiFePO4 batteries Specifications Input (Operating) Voltage 9 - 32VDC Output System Voltage 12VDC Maximum Charging Voltage 15.3V Output Current Rating (Cont.) 25A Input Fuse Rating 40A Output Fuse Rating 40A Type Approval E-Mark Warranty 2 Years Standby Current Draw <100mA Output Power 375W Width (mm) 120 Height (mm) 37 Length (mm) 165 Weight (kg) 1 Videos

 The Manager30 is a complete battery management system for charging auxiliary batteries used in recreational automotive and marine applications. The dual battery system incorporates AC, DC, and solar inputs to achieve the best charge for an auxiliary battery.Developed with ease of installation in mind, The Manager30 is compatible with all vehicles and alternator systems including variable voltage alternators.Whether you’re charging Lead Acid, Gel, Calcium, AGM, or Lithium Iron Phosphate batteries, The Manager30 represents a complete DC to DC charging and maintenance solution. If you’re charging one auxiliary battery or more, The Manager30 will ensure they’re always fully charged, providing peace of mind when battery charge provides the power source for the comforts of home whilst traveling around Australia.The Manager30 operates like 6 separate products, it charges an auxiliary battery from the vehicle while on the move, it’s a 240-volt charger, a solar regulator, a battery isolator, a load disconnect controller, all with a remote battery monitor, making it market-leading. Charging lithium batteries Lithium batteries have improved storage capacity relative to size and weight. They do however require specific charging conditions in order to operate correctly and the battery itself must have an in-built cell management system. REDARC has designed a charging profile within The Manager30 to complement these in-built systems.   Green power priority The Manager30 is designed to charge an auxiliary battery from multiple sources simultaneously. If 12 volt solar power is available, solar power will be used before topping up the output charging current from another source mains (if available) or DC vehicle power when on the move.   MPPT solar regulator The built-in Maximum Power Point Tracking (MPPT) solar regulator allows The Manager30 to deliver the maximum amount of power from portable solar panels, even during low light conditions.   Remote monitor Designed to show you auxiliary battery information and charge status. You can customize how your battery is charged and monitor where the charge is coming from. A user-friendly, graphical display monitor lets you know what’s going on, keeping you in control at all times.   Features Multi-Stage AC-DC Battery Charger Multi-Stage DC to DC Charger Maximum Power Point Tracking Solar Regulator Battery Monitor Dual Battery Isolator Load Disconnect Controller Super quiet operation Charges AGM, Gel, Calcium content, VRLA, Standard Lead Acid, and LiFePO4 batteries Tested to mains power safety standards in Australia Specifications Output System Voltage 12VDC Maximum Charging Voltage 16.0V* (*Calcium setting in storage mode) Output Current Rating (Cont.) 30A Output Power 520W Input Fuse Rating 40A Output Fuse Rating 40A Warranty 2 Years Protection Short Circuit, Surge, Reverse Polarity, Overload Input (Operating) Voltage 240VAC / 9 - 32VDC Length (mm) 445 Width (mm) 185 Height (mm) 79 Weight (kg) 5.5 AC Mains Plug Type AU, NZ, EU Type Approval CE Videos

The next-generation Manager30 S3 model is the complete battery management system for charging auxiliary batteries used in 4wd, camper recreational automotive, and marine applications. The dual battery system incorporates AC, DC, and solar inputs to achieve the best charge for an auxiliary battery. Has been developed with ease of installation in mind, The Manager30 is compatible with all vehicles and alternator systems including variable voltage alternators. Whether you’re charging Lead Acid, Gel, Calcium, AGM, or Lithium Iron Phosphate batteries, The Manager30 represents a complete DC to DC charging and maintenance solution. If you’re charging one auxiliary battery or more, The Manager30 will ensure they’re always fully charged, providing peace of mind when battery charge provides the power source for the comforts of home whilst travelling around Australia. The Manager30 operates like 6 separate products, it charges an auxiliary battery from the vehicle while on the move, it’s a 240-volt charger, a solar regulator, a battery isolator, a load disconnect controller, all with a remote battery monitor, making it market-leading.   Charging lithium batteries Lithium batteries have improved storage capacity relative to size and weight. They do however require specific charging conditions in order to operate correctly and the battery itself must have an in-built cell management system. REDARC has designed a charging profile within The Manager30 to complement these in-built systems.   Green power priority The Manager30 is designed to charge an auxiliary battery from multiple sources simultaneously. If 12-volt solar power is available, solar power will be used before topping up the output charging current from another source mains (if available) or DC vehicle power when on the move.   MPPT solar regulator The built-in Maximum Power Point Tracking (MPPT) solar regulator allows The Manager30 to deliver the maximum amount of power from portable solar panels, even during low light conditions.   Remote monitor Designed to show you auxiliary battery information and charge status. You can customize how your battery is charged and monitor where the charge is coming from. A user-friendly, graphical display monitor lets you know what’s going on, keeping you in control at all times.   Features Multi-Stage AC-DC Battery Charger Multi-Stage DC to DC Charger Maximum Power Point Tracking Solar Regulator Battery Monitor Dual Battery Isolator Load Disconnect Controller Super quiet operation Charges AGM, Gel, Calcium content, VRLA, Standard Lead Acid, and LiFePO4 batteries Tested to mains power safety standards in Australia   Charging lithium batteries Lithium batteries have improved storage capacity relative to size and weight. They do however require specific charging conditions in order to operate correctly and the battery itself must have an in-built cell management system. REDARC has designed a charging profile within The Manager30 to complement these in-built systems.   Green power priority The Manager30 is designed to charge an auxiliary battery from multiple sources simultaneously. If 12-volt solar power is available, solar power will be used before topping up the output charging current from another source mains (if available) or DC vehicle power when on the move.   MPPT solar regulator The built-in Maximum Power Point Tracking (MPPT) solar regulator allows The Manager30 to deliver the maximum amount of power from portable solar panels, even during low light conditions.   Remote monitor Designed to show you auxiliary battery information and charge status. You can customize how your battery is charged and monitor where the charge is coming from. A user-friendly, graphical display monitor lets you know what’s going on, keeping you in control at all times.   Multi-Stage AC-DC Battery Charger Multi-Stage DC to DC Charger Maximum Power Point Tracking Solar Regulator Battery Monitor Dual Battery Isolator Load Disconnect Controller Super quiet operation Charges AGM, Gel, Calcium content, VRLA, Standard Lead Acid and LiFePO4 batteries Tested to mains power safety standards in Australia   SPECIFICATIONS   Output System Voltage 12VDC Maximum Charging Voltage 16.0V* (*Calcium setting in storage mode) Output Current Rating (Cont.) 30A Output Power 520W Input Fuse Rating 40A Output Fuse Rating 40A Warranty 2 Years Protection Short Circuit, Surge, Reverse Polarity, Overload Input (Operating) Voltage 240VAC / 9 - 32VDC Length (mm) 445 Width (mm) 185 Height (mm) 79 Weight (kg) 5.5 AC Mains Plug Type AU, NZ, EU Type Approval CE   VIDEOS

    BMS1230S3R Manual The Manager30 BMS1230S3R features both the RedVision display screen and mobile phone connectivity for complete battery management for charging auxiliary batteries used in recreational automotive and marine applications. The dual battery system incorporates AC, DC and solar inputs to achieve the best charge for an auxiliary battery. This 30amp charger is the complete battery management system that gives you the best of both worlds. Whether you’re free camping or on a powered site, it knows how to take charge and keep auxiliary batteries fully charged. The Manager30 operates like 6 separate products, it charges an auxiliary battery from the vehicle while on the move, it’s a 240-volt charger, a solar regulator, a battery isolator, a load disconnect controller, all with a remote coloured RedVision battery monitor, making it market-leading. The RedVision remote battery monitor is designed to show auxiliary battery information and charge status through its coloured display. You can customise how your battery is charged and monitor where it is coming from. It also provides full connectivity to the Manager30 via the RedVision Smartphone App on both Apple and Android devices. Whether you’re charging Lead Acid, Gel, Calcium, AGM or Lithium Iron Phosphate batteries, The Manager30 represents a complete DC to DC charging and maintenance solution. If you’re charging one auxiliary battery or more, The Manager30 will ensure they’re always fully charged, providing peace of mind when battery charge provides the power source for the comforts of home whilst travelling around Australia. Developed with ease of installation in mind, The Manager30 is compatible with all vehicles and alternator systems including variable voltage alternators.   RedVision monitor The Manager30 comes with a display designed to give you house battery information and charge status along with critical system information while charging is in progress. With the display, you can customise how your house battery is charged and monitor where the charge is coming from, keeping you in control at all times. The display can be surface mounted on a wall or recessed (into the dashboard of an RV for example). The display also allows a Bluetooth connection to your Smartphone, via the RedVision App, which provides the same data and control available on the display all in the palm of your hand.   Charging lithium batteries Lithium batteries (LiFeP04) have improved storage capacity relative to size and weight. They do however require specific charging conditions in order to operate correctly and the battery itself must have an in-built cell management system. REDARC have designed a charging profile within The Manager30 to complement these in-built systems.   Green power priority The Manager30 is designed to charge an auxiliary battery from multiple sources simultaneously. If 12-volt solar power is available, solar power will be used before topping up the output charging current from another source mains (if available) or DC vehicle power when on the move.   MPPT solar regulator The built-in Maximum Power Point Tracking (MPPT) solar regulator allows The Manager30 to deliver the maximum amount of power from portable solar panels, even during low light conditions.   Features          Multi-Stage AC-DC Battery Charger          Multi-Stage DC to DC Charger          Maximum Power Point Tracking Solar Regulator          Improved, 4.3” coloured RedVision display battery monitor          RedVision display allows connection to Smartphone via App          Dual Battery Isolator          Load Disconnect Controller          Super quiet operation          Charges AGM, Gel, Calcium content, VRLA, Standard Lead Acid and LiFePO4 batteries          Tested to mains power safety standards in Australia Specifications Output System Voltage 12VDC Maximum Charging Voltage 16.0V* (*Calcium setting in storage mode) Output Current Rating (Cont.) 30A Output Power 520W Input Fuse Rating 50A Output Fuse Rating 40A Protection Short Circuit, Surge, Reverse Polarity, Overload Input (Operating) Voltage 220-240VAC / 9 - 32VDC Length (mm) 445 Width (mm) 185 Weight (kg) 5.5 AC Mains Plug Type AU, NZ, EU Type Approval CE Warranty 2 Years

Enerdrive ePOWER DC2DC+ Battery Charger 40A ePower DC to DC battery charger is smaller than the Enerdrive most compact AC Battery Charger. Two totally independent DC Inputs for both engine and solar regulation charging one house battery bank output DC M6 screw terminals that will allow for large battery cable connection between all sources A dedicated Maximum Power Point (MPPT) solar regulator The same battery algorithms as included in our AC mains ePOWER battery charger. GEL, AGM, Flooded, Lithium and the ability to create  a full custom profile Vehicle input allows for either 12 or 24v and a maximum solar input of 45V/800W 40A output up to 40+°C with thermo controlled fan cooling Fully programmable LCD display to show which source is charging the battery along with charger status, voltage and amperage Temperature sensor included in charger for more accurate battery charging The Enerdrive ePOWER DC2DC+ Battery Charger is a fully automatic multistage, multi input battery charger with the ability to charge from either an alternator linked to a battery; or via solar power with the in built Maximum Power Point Tracking (MPPT) Solar Controller. With two inputs available, the main/house battery will be charged from either the engine while underway, or via the solar panels when stationary. The process to choose either engine or solar is fully automatic and both functions are controlled from within the unit itself without the need for external relays. During normal operation the ePOWER DC2DC+ Battery Charger will do a full charge cycle to float stage on the house battery bank with ability to choose either GEL, AGM, Flooded, Custom Programmable or Lithium. Once float stage is reached the charger transitions to a power supply mode to support any on-board DC loads. Multistage Charging Process The ePOWER DC2DC+ Battery Charger is a fully automatic, set and forget charger. It is designed to quickly and accurately recharge your deep cycle batteries utilising charger algorithms that help to maximise the life of your specialised deep cycle batteries. The ePOWER DC2DC+ Battery Charger features multistage smart charging technology that enables the charger to be connected to your battery bank permanently. With the input of multiple sources, you can be assured of charging your batteries whenever underway; or when the sun is shining on your solar array. As dictated by battery manufacturer’s recommendations, deep cycle batteries require a multistage charge sequence for perfect, fast and accurate charging. The Enerdrive ePOWER DC2DC+ smart charger delivers three primary charge stages. Stage 1 – Bulk or Boost charge; The battery is charged at full rated output current of the charger until the battery reaches its final charging voltage, known as its absorption voltage. In this step, around 80% of the battery is recovered as fast as possible. Stage 2 – Absorption Charge; With the charger voltage held steady, the remaining 20% is replaced with the charger allowing the current to taper off as the battery approaches full charge. Stage 3 – Float; Finally, in the float stage the charger voltage is lowered and held at a constant and safe predetermined level. This prevents the battery from being overcharged, yet allows the charger to supply enough current to make up for the self-discharge losses of the battery, while supporting any additional loads connected to the battery (such as DC lighting and refrigerators). This stage allows for the charger to be used as a DC power supply. Smart Charging Feature The ePOWER DC2DC+ Battery Charger will regulate its output based on the loads connected to your battery bank. This function is important to maintain the life of your battery bank as some battery chargers mistake loads for discharge and continue to keep the batteries in the bulk or absorption stage for extended periods of time, which will damage the battery bank. The ePOWER DC2DC+ Battery Charger has two methods of load based regulation to ensure your battery charger transitions to float when it should do so.