4WD & Offroad (32)

Redarc Pressure & Oil Temperature 52mm Gauge with Optional Temperature Display, 2-year warranty. The REDARC 52mm single oil pressure & oil temperature gauge is ideal for monitoring your engines oil pressure and oil temperature. The G52-POT gauge is supplied with one REDARC oil pressure sensor that displays from 0 to 80 PSI and a REDARC ¼ NPT thread oil temperature sensor that displays from 60 to 150 degrees Celsius. Monitoring oil pressure ensures the longevity of your vehicle and allows you to ensure that the correct pressure is maintained so that your car bearings are well lubricated. This is crucial when travelling at continuous high speeds and towing heavy loads. Low oil pressure can be an indicator of a low oil level, diluted or worn out oil, worn engine bearings, high oil temperature or a worn oil pump. Oil subjected to excessive temperatures can lose its lubrication properties that keep metal parts from touching. If the oil temperature rises above the desired limit, you can reduce the load placed on the engine or transmission to reduce the temperature and prevent engine failure. Temperature Sensor  The G52-POT gauge also supports one of four optional temperature sensors. You will need to purchase one of the following REDARC temperature sensors to equip the gauge with this function: GS-UT-80: An NTC temperature sensor in a plastic housing for measuring cabin, fridge or outside temperature. The range is -20~+80°C. This sensor is supplied with a 6-metre extension cable. GS-UT-120: An NTC temperature sensor in a metal copper housing with 6mm diameter mounting hole. The range is -20~+120°C. This sensor is supplied with a 6-metre extension cable. GS-OWT1-4: Water or Oil temperature sender. 1/4 NPT threaded. Designed to measure from -20~ +170°C. Supplied with a 3-metre extension cable. GS-OWT1-8: Water or Oil temperature sender. 1/8 NPT threaded. Designed to measure from -20~ +170°C. Supplied with a 3-metre extension cable. The G52-POT gauge diameter requires a 52mm hole for mounting. REDARC offer a range of mounting solutions including a 2” black plastic mounting cup (GH-CUP) and one (GH-MP1), two (GH-MP2) and three (GH-MP3) hole gauge mounting panels. Radio inserts are also available that suit the Toyota Hilux (GH-RI05). The REDARC 24 to the 12-volt adaptor (GA-2412V) can be used to connect this gauge to a vehicle with a 24-volt ignition and lighting supply, however, only a 12-volt battery can be monitored. Enhanced Lighting Controller  REDARC recommends the purchase of an Enhanced Lighting Controller (GA-ELC) with this gauge. The GA-ELC is designed to enhance the lighting of your REDARC gauges as only one required for a set. It is to be used when you do not have a dimming circuit to connect your gauge to or the dimming circuit in your vehicle does not dim the REDARC gauge to your liking. The GA-ELC also allows you to program nighttime brightness and colour of your REDARC gauges, including dimming if connected to a dash dimmer. Once programmed your gauges will change colour when turning on your park lights and back to a daylight colour when you turn them off. The GA-ELC is also 24 volt capable. Features: Satin Chrome Bezel. 13 Selectable Backlight Colours. Multiple programmable alert levels with amber or red backlight and audible beep. Display illuminates when park lights are turned on so you can check battery voltages and discharge or charge current without turning on the ignition. If fitting more than one REDARC gauge, a communications link can be connected between the gauges to change the backlight colour all at once. Specifications Warranty 2 Years Sensor(s) (Included) GS-P-150, GS-OWT1-4 Sensor (Optional) GS-UT-80 / GS-UT-120 / GS-OWT1-4 / GS-OWT1-8 Standby Current Draw 30mA Input (Operating) Voltage 6 - 16V Height (mm) 42 Weight (kg) 0.05

Redarc Universal Tow-Pro Wiring Kit, 2-Year Warranty. The REDARC TPWKIT-013 Universal Tow-Pro Wiring Kit supports the installation of the Tow-Pro Elite electric trailer brake controller into a wide range of vehicles. It is suitable for vehicles where the start battery, Tow-Pro main unit, and the cable run to the cabin are all in-line, via a 1.8m power cable length. The Universal Tow-Pro Wiring Kit range replaces the Tow-Pro Wiring Kit range and consolidates the range from 10 kits down to 3. The Universal Tow-Pro Wiring Kit comes with the complete range of hardware required to install a Tow-Pro Elite brake controller and contains a Wago Boot, Protection Device, Wiring Harness, Mounting Bracket, and fitting instructions. REDARC’s new Universal range of Wiring Kits feature technology that enables compatibility with modern driver aids such as Autonomous Emergency Braking, Adaptive Cruise Control, lane departure, collision avoidance, and where the vehicle brake signal may be generated from different systems. By using a REDARC Tow-Pro Wiring Kit you ensure the quick and high-quality installation of Australia’s favourite brake controller, the Tow-Pro Elite. REDARC offers a wide range of accessories to aid and assist the install of the market-leading Tow-Pro Elite into most vehicles including Switch Inserts, Remote Head Wiring Kits, Encapsulated Protection Devices, and a Mounting Bracket Kit. Redarc has created this Universal Tow-Pro kit to replace the old TPWKIT-002, TPWKIT-004, TPWKIT-006, TPWKIT-007 and TPWKIT-009 kits    

An exhaust jack is the perfect tool for recovering a four wheel drive vehicle stuck in deep sand or other areas where conventional jacks may sink, or when the vehicle is simply too low for any other jack to fit. If the vehicle is stuck up to the chassis rails, a thin area can be dug out just below the rails to allow for the deflated air bag jack to slip underneath. The design and included parts of the air bag jack then allow for it to be connected to the exhaust of the vehicle to inflate the jack. Once raised, the area underneath the vehicles wheels can then be filled in or have tracks placed below to provide extra grip, making for a painless recovery.With no moving metal parts, the exhaust jack is also safer than hi-lift jacks, and can be packed away in the supplied bag for convenient storage. SPECIFICATIONS Part No. TDR04016 Type AIR JACK Brand THUNDR Unit of Measure EACH Description Exhaust Powered Jack Warranty 1Y Note Exhaust operated recovery air bag Weight 6.7kg   VIDEOS  

edarc 30 Amp Solar Regulator with Anderson Connection, 2 Years Warranty. The REDARC 30A Solar Regulator ensures the correct charge is supplied safely and efficiently to charge an auxiliary battery and is ideal when multiple REDARC solar blankets are used simultaneously. Available with Anderson™ SB™50 connectors. REDARC’S newly designed 30 Amp Solar Regulator comes with the Anderson™ SB™50 connectors and is ideal for use when multiple REDARC solar blankets are used simultaneously. REDARC’s 30 Amp Solar Regulator acts as the go between to transfer power generated from the panels to the battery. Featuring multistage charging; boost, absorption and float, REDARC’s 30 Amp Solar Regulator ensures that the correct charge is supplied safely and efficiently to the battery and will protect it from over charging. It will work with multiple chemistry batteries including AGM, Standard and Calcium*, is ideal for permanent installation or portable systems, and has multiple levels of protection including over temperature, over charge and reverse polarity. What’s more set up is now even easier thanks to genuine industry standard Anderson™ SB™50 connectors. These high quality Anderson™ plugs are simple and fast to connect with no screw terminals and no risk of poor connections from frayed wires or loose terminals – just plug and play! *Battery default setting is AGM. REDARC recommends the purchase of the REDARC Solar Remote Monitor to change battery types and configuration settings. Features: Multi-stage charging- boost, absorption, and float Works with multiple battery types (REDARC Solar Remote Monitor required) Ideal for permanent installation or portable systems Multiple levels of protection – over temperature, over charge, reverse polarity Genuine Industry Standard Anderson™ SB™50 plug connection Part No. SRPA0360 Type VOLTAGE REGULATOR Brand REDARC Unit of Measure EACH Description Redarc 30A Solar Regulator Anderson Connection Warranty One Year Weight 3kg Amps 30A Input Voltage 19-30v / 32-50v Output Voltage 9-16v / 18-32v Stages Dual Features • 30A• Compatible with 12 or 24 volt solar panels• PWM multi-stage charging with selectable battery chemistry types• Safely charges dual battery systems• Protects battery from overcharging• Provides three-stage charging of various battery types

Redarc 20 Amp Solar Regulator with Anderson Connection, 2 Years Warranty. The REDARC 20A Solar Regulator ensures the correct charge is supplied safely and efficiently to charge an auxiliary battery. Available with Anderson™ SB™50 connectors. REDARC’S newly designed 20 Amp Solar Regulator comes with the Anderson™ SB™50 connectors and works with the 150W and 190W SunPower® cell blanket. REDARC’s 20 Amp Solar Regulator acts as the go-between to transfer the power generated from solar panels to the battery. Featuring multistage charging; boost, absorption and float, REDARC’s 20 Amp Solar Regulator ensures that the correct charge is supplied safely and efficiently to the battery and will protect it from overcharging. It will work with multiple chemistry batteries including AGM, Standard and Calcium*, and is ideal for permanent installation or portable systems, and has multiple levels of protection including over temperature, over charge and reverse polarity. What’s more set-up is now even easier thanks to genuine industry-standard Anderson™ SB™50 connectors. These high-quality Anderson™ plugs are simple and fast to connect with no screw terminals and no risk of poor connections from frayed wires or loose terminals – just plug and play! Features: Multi-stage charging- boost, absorption, and float Works with multiple battery types (REDARC Solar Remote Monitor required) Ideal for permanent installation or portable systems Multiple levels of protection – over temperature, over charge, reverse polarity Genuine Industry Standard Anderson™ SB™50 plug connection Part No. SRPA0240 Type VOLTAGE REGULATOR Brand REDARC Unit of Measure EACH Description Redarc 20A Solar Regulator Anderson Connection Warranty One Year Note Remote Solar Monitor to suit SRPA-RM Weight 3kg Amps 20A Input Voltage 19-30v / 32-50v Output Voltage 9-16v / 18-32v Stages Multi Features • Compatible with 12 or 24 volt solar panels• PWM multi-stage charging with selectable battery chemistry types• 20A• Safely charges dual battery systems• Protects battery from over charging• Provides three-stage charging of various battery types

REDARC solar regulators come with an informative, user friendly remote monitor which allows you to keep track of what your solar panels are producing and the state of your battery. Note: This product is only compatible with our 10 & 20A Solar Regulator (SRP0 range) Features Informative LCD Display Voltage, Current and Power Information Fault Detection Easy to use Includes a 10m RJ45 cable Specifications Warranty 2 Years Length (mm) 95 Width (mm) 95 Height (mm) 24 Weight (kg) 0.105

Thunder 150 Watt Solar Panel, 1-year warranty.  With the increasing popularity of free camping and the plethora of electronic gadgets being relied on during these getaways, constant, reliable and portable power is more necessary than ever. Whilst generators have long since been the preferred option for providing off-grid power, their excessive weight and noise make them an undesirable choice. Advances in 12 volt technology and a preference towards greener solutions are driving generators to obsolescence. Most camping electronics can be run from aquality 12 volt system, and with the addition of a solar charging solution, batteries will be running for weeks without requiring a 240 volt boost. The Thunder range of solar panels are made of high quality monocrystalline solar cells which provide maximum efficiency and longevity. Thunder solar panels ensureyou have a dependable source of power without occupying excessive space or polluting that peaceful camping experience with excess noise. Part No. TDR15004 Type SOLAR PANEL Brand THUNDER Unit of Measure EACH Description Thunder Solar Panel 150W Warranty One Year Depth / Thickness 35mm Watts 150 Open Circuit Voltage 22.14 Regulator Type External Short Circuit Current 9.35 Type Monocrystalline Note Panel fitted with Anderson style connector Weight 4.5kg Width 680mm Height 1480mm Item Type TBC Output Voltage 18.45 Features • Panel fitted with Anderson style connector• Monocrystalline• Open circuit voltage: 22.14V• Short circuit current: 9.35A• External regulator type• Output voltage: 18.45V• Dimensions: 1480 x 680 x 35mm• Weight: 12kg

Thunder 120 Watt Solar Panel, 1-year warranty. With the increasing popularity of free camping and the plethora of electronic gadgets being relied on during these getaways, constant, reliable and portablepower is more necessary than ever. Whilst generators have long since been the preferred option for providing off-grid power, their excessive weight and noise makethem an undesirable choice. Advances in 12-volt technology and a preference towards greener solutions are driving generators to obsolescence. Most camping electronics can be run from athe quality 12-volt system, and with the addition of a solar charging solution, batteries will be running for weeks without requiring a 240-volt boost. The Thunder range of solar panels are made of high quality monocrystalline solar cells which provide maximum efficiency and longevity. Thunder solar panels ensureyou have a dependable source of power without occupying excessive space or polluting that peaceful camping experience with excess noise Part No. TDR15003 Type SOLAR PANEL Brand THUNDER Unit of Measure EACH Description Thunder Solar Panel 120W Warranty One Year Depth / Thickness 35mm Watts 120 Open Circuit Voltage 22.08 Regulator Type External Short Circuit Current 7.5 Type Monocrystalline Note Panel fitted with Anderson style connector Weight 4kg Width 680mm Height 1130mm Item Type TBC Output Voltage 18.4 Features • Panel fitted with Anderson style connector• Monocrystalline• Open circuit voltage: 22.8V• Short circuit current: 7.5A• External regulator type• Output voltage: 18.4V• Dimensions: 1130 x 680 x 35mm• Weight: 8.5kg

Redarc 50 Watt Monocrystalline Solar Panel, 2 yr-warranty. REDARC standard monocrystalline flat panels are highly efficient with a robust design. A tempered glass coating and a sturdy aluminium frame ensure that our panels will withstand harsh road conditions and extreme weather conditions. Each panel is tested at the time of manufacture to conform to CE standards, so you can be sure that the panel output is exactly as described in its specification. Features Monocrystalline construction Strong Aluminium Frame Tempered glass coating Diode protected 5-year structural warranty 25yr/80% efficiency warranty   Part No. SMSP1050 Type SOLAR PANEL Brand REDARC Unit of Measure EACH Description Redarc 50W Monocrystalline Fixed Solar Panel Warranty Five Years Depth / Thickness TBC Watts TBC Open Circuit Voltage TBC Regulator Type TBC Short Circuit Current TBC Type TBC Width TBC Height TBC Item Type TBC Output Voltage TBC Features • Designed for fixed intallation, typically on the roof area of caravans, RV's & motorhomes, as well as some camper trailer and 4x4 vehicle applications• Anodised aluminium frame and tempered glass coating• MC4 connectors for easy installation• Feature Monocrystalline cells which have a high cell conversion efficiency of 20.6%• Compatible with existing ABS mounts

Projecta Automatic 12/24V 45A 4 Stage Solar Charge Smart Controller, 1 Year- Warranty. Ideal for larger deep-cycle battery banks often found in motor homes, houseboats and remote shacks. This sophisticated controller boasts a host of intelligent features enabling the user to customise the charge settings to maximise battery life and performance. Features: Digital L.E.D screen: Displays battery voltage, charging current, charging capacity, fault codes and more. Dual USB ports: 5V 2.4A USB ports for powering directly from the controller.  Multi-chemistry: Set the charging profile to suit battery chemistry type: Wet, AGM or Gel, or user settings.  Low voltage disconnect: Set the disconnect voltage point to best suit your application, protecting your battery from over-discharge. Temperature sensor: Built-in sensor enables the unit to optimise charge performance and offer additional protection. Optional sensor probe also available Description Projecta Automatic 12/24V 45A 4 Stage Solar Charge Smart Controller, 1 Year Warranty SKU SC245 Brands Projecta Product Category Solar Charge Controllers Amps 45.0 Amps Product Type Solar Charge Controller Voltage 12V Charge voltage 'absorption' Gel: 14.2V | AGM: 14.4V | Wet: 14.7V Recommended Solar Panel Size 540W Maximum Solar Watt Input 50VDC, 45A Input Voltage 12V Type Approval EMC NOTE To suit Projecta Fixed Solar Panel Manufacturers Warranty 1 Year

Projecta Solar Charge Remote Control, 1 Year-Warranty. Maintain your power system from a convenient location and maximise your battery life and performance by customising the charge settings to best suit your battery. Features: Multi-chemistry:   Set the charging profile to suit battery chemistry type: Wet, AGM or Gel, or user settings Battery size: Set the battery size (Ah) to ensure power calculations are accurate Customisable settings: Total user control enables low voltage disconnect set points, charge rate control and more Recall data: Recall daily and monthly power usage levels, charge rate and battery charge level information  Description Projecta Solar Charge Remote Control, 1 Year Warranty SKU SC300D Brands Projecta Product Category Accessories Product Type Solar Charge Controller Dimensions (WxHxL mm) 114 x 114 x 32.7 Input Voltage 12V Battery 12V Manufacturers Warranty 1 Year NOTE To suit Projecta Fixed Solar Panel

Projecta Automatic 12/24V 60A 4 Stage Solar Charge Smart Controller, 1 Year Warranty. Ideal for larger deep-cycle battery banks often found in motor homes, houseboats and remote shacks. This sophisticated controller boasts a host of intelligent features enabling the user to customise the charge settings to maximise battery life and performance.. Features: Digital L.E.D screen:   Displays battery voltage, charging current, charging capacity, fault codes and more. Dual USB ports: 5V 2.4A USB ports for powering directly from the controller. Multi-chemistry: Set the charging profile to suit battery chemistry type: Wet, AGM or Gel, or user settings. Low voltage disconnect: Enables you to protect your battery from over-discharge. Temperature sensor: Built-in sensor enables the unit to optimise charge performance and offer additional protection. Optional sensor probe also available.     Short Description Projecta Automatic 12/24V 60A 4 Stage Solar Charge Smart Controller, 1 Year Warranty SKU SC260 Brands Projecta Product Category Solar Charge Controllers Amps 60.0 Amps Product Type Solar Charge Controller Voltage 12V Charge voltage 'absorption' Gel: 14.2V | AGM: 14.4V | Wet: 14.7V Recommended Solar Panel Size 720W Maximum Solar Watt Input 50VDC, 60A Input Voltage 12V Type Approval EMC NOTE To suit Projecta Fixed Solar Panel Manufacturers Warranty 1 Year

Projecta Automatic 12V 10A 4 Stage Solar Charge Controller, 1 Year- Warranty. Packed with features, this sophisticated solar controller is ideal for panels capable of producing up to 10 Amps. Delivering a comprehensive 4 stage charging process and the ability to tailor its settings to best suit your battery type. Features: Digital L.E.D screen: Displays battery voltage, charging current, charging capacity, fault codes and more L.E.D charge indicator: Displays quick reference to charge status and battery condition Multi-chemistry: Set the charging profile to suit battery chemistry type: Wet, Calcium, AGM or Gel Sealed electronics: Conformal coated circuit board and plated terminals protect the controller from the elements Temperature sensor: Built-in sensor enables the unit to optimise charge performance and offer additional protection. Optional sensor probe also available.

Thunder 20 Amp DC-DC Charger with Solar Input, 1 Year-Warranty. Compact in size and easy to install, the new Thunder DC-DC Charger is the smart way to charge your auxiliary battery, no matter your vehicle. Utilising a unique pulse charging algorithm with the intelligence to determine the best charge rate for your auxiliary battery, this charger is the perfect addition to any vehicle requiring the management of a dual battery setup. One of the greatest features of the new DC-DC Battery Charger is the new remote Bluetooth LCD screen; giving you better visibility of your battery’s state of charge. The new charger also features Modular Sense Technology (MST) allowing you to link multiple units together giving you a 20, 40 or 60A output without having to outlay for a larger unit upfront. Suitable for Gel, AGM, Calcium, Lead Acid and now Lithium batteries, Thunder’s new DC-DC Charger is an ideal addition for caravans, camper trailers and 4WD’s. Sleek new heavy duty aluminium case Easy to read remote mount Bluetooth LCD screen 12-24V System input with 12V output Upgraded operating temperature of 0-90° allowing under bonnet mounting IP67 Rated – water and dust proof, ready for harsh environments New linkable design to easily increase amperage outputs using Modular Sense Technology Microchip monitoring and control fully automates high frequency multistage charging Pulse mode technology that reduces oxidation and minimises temperature equating to longer battery life Unit will automatically change charge rate mapping for GEL, AGM and standard Lead Acid New Lithium battery charging profile option Internal charger temperature monitoring and power output control Over charging, short circuit and over temperature protection Reverse polarity protection New 50V solar input with MPPT regulated output allowing 300W of solar Integrated Bluetooth LCD Screen   The remote LCD interface screen gives you better visibility on your battery’s state of charge, without looking directly at the unit. This design, its IP67 rating and 90°C operating temperature means the charger can be installed in an engine bay with a reduced likelihood of it de-rating due to the harsh under bonnet environment, with the display in the cabin. While your vehicle is charging, the LCD screen will show the Vehicle Car Charge screen, allowing you to see the main and auxiliary battery voltages, auxiliary battery percentage and how much current is flowing into the battery. It will also show if Lithium mode is being used. After the vehicle’s engine has been turned off and the battery voltage in the main battery has reached a loaded voltage of 12.2V, the LCD screen will move to the Solar Charge screen showing battery voltages, percentages and the flow of the solar charge. THE REMOTE MOUNT DIFFERENCE Clear visual display of state of charge of all batteries IP67 rating and 90°C operating temperature means the charger can be installed in an engine bay with a reduced likelihood of it de-rating due to the harsh under bonnet environment Easily identify and rectify battery faults Easily identify if your batteries are charged by the alternator or solar Vehicle Car Charge Screen Bluetooth active Main battery voltage Auxiliary battery voltage DC-DC current output Vehicle charge flow Auxiliary battery percentage Main battery charge level Auxiliary battery charge level Battery fault indicator Display switch Lithium mode Solar Charge Screen Bluetooth active Main battery voltage Auxiliary battery voltage Solar charge flow Main battery percentage Auxiliary battery percentage Main battery charge level Auxiliary battery charge level Battery fault indicator Display switch Lithium mode

Thunder 20 AMP DC-DC Charger, 1-year warranty. Easy to install, the Thunder DC to DC charger is the smart way to charge your auxiliary battery, no matter your vehicle. The Thunder DC-DC Charger utilises a unique pulse charging algorithm with the intelligence to determine the best charge rate for your auxiliary battery (excluding lithium). Features: MPPT solar regulator will regulate solar panels at maximum efficiency capable of up to 300W of solar @ 25V 20A output to charge your auxiliary battery while driving Automatically switches to the solar input when the vehicle battery is turned off or the main battery drops to 12.2V Splash resistant (not IP rated) Easy to read and comprehensive LED display Simple to install – 4 mounting holes and 4 easy-to-use wiring studs The rate of charge starts to decrease at 50 degrees and willfully cut out at 80 degrees Easy to install, the Thunder DC to DC charger is the smart way to charge your auxiliary battery, no matter your vehicle. Utilising a unique pulse charging algorithm with the intelligence to determine the best charge rate for your auxiliary battery (excluding lithium), this charger is the perfect addition to any vehicle requiring the management of a dual battery setup. Thunder helps take you places you’ve never been before, making adventure more affordable and accessible for 4WD enthusiasts. Designed for the working adventurer, Thunder products have been tested and developed to handle anything you can throw at them without breaking the bank. Description Thunder 20 AMP DC-DC Charger, 1 Year Warranty SKU TDR02020 Brands Thunder Product Category Battery Chargers Model TDR02020 Output Current Rating (Amps) 20.0 Amps Float 13.8V Standby Current 3mA Battery Range 18 to 250Ah Operating Temperature Range 0°C to 60°C (current derates after 60° Output 20A Output System Voltage 12V Input Fuse Rating Minimum 30A Output Fuse Rating Minimum 30A Charging Voltage 13.1V - 15.2V (stops charging when alternator or vehicle battery below 12.2V) Net Weight (kg) 1.5 Kg Solar Input Voltage Range 13V-25V Maximum Solar Watt Input 300W Note: Exceeding 300W of Solar will damage the Thunder DC-DC charger Input Voltage 12.2V - 17V Note: If voltage increases over 17V the Thunder DC-DC will shut off, reset will be needed. Manufacturers Warranty 1 Year

Redarc Single Oil Pressure 52mm Gauge with Optional Temperature Display, 2-year warranty. The REDARC 52mm single oil pressure gauge is ideal for monitoring your engines oil pressure. The G52-PT gauge is supplied with one oil pressure sensor from REDARC that displays from 0 to 130 PSI. This gauge is designed to monitor the oil pressure of your vehicle's engine. Monitoring oil pressure ensures the longevity of your vehicle and allows you to ensure that the correct pressure is maintained so that your car bearings are well lubricated. This is crucial when travelling at continuous high speeds and towing heavy loads. Low oil pressure can be an indicator of a low oil level, diluted or worn out oil, worn engine bearings, high oil temperature or a worn oil pump. Temperature Sensors The G52-PT gauge also supports one of four optional temperature sensors. You will need to purchase one of the following REDARC temperature sensors to equip the gauge with this function: GS-UT-80: An NTC temperature sensor in a plastic housing for measuring cabin, fridge or outside temperature. The range is -20~+80c. This sensor is supplied with a 6-metre extension cable. GS-UT-120: An NTC temperature sensor in a metal copper housing with a 6mm diameter mounting hole. The range is -20~+120c. This sensor is supplied with a 6-metre extension cable. GS-OWT1-4: Water or Oil temperature sender. 1/4 NPT threaded. Designed to measure from -20~ +170c. Supplied with a 3-metre extension cable. GS-OWT1-8: Water or Oil temperature sender. 1/8 NPT threaded. Designed to measure from -20~ +170c. Supplied with a 3-metre extension cable. The G52-PT gauge diameter requires a 52mm hole for mounting. REDARC offer a range of mounting solutions including a 2” black plastic mounting cup (GH-CUP) and one (GH-MP1), two (GH-MP2) and three (GH-MP3) hole gauge mounting panels. Radio inserts are also available that suit the Toyota Hilux (GH-RI05). The REDARC 24 to 12 Volt adaptor (GA-2412V) can be used to connect this gauge to a vehicle with a 24-volt ignition and lighting supply, however, only a 12-volt battery can be monitored. Enhanced Lighting Controller  REDARC recommends the purchase of an Enhanced Lighting Controller (GA-ELC) with this gauge. The GA-ELC is designed to enhance the lighting of your REDARC gauges as only one required for a set. It is to be used when you do not have a dimming circuit to connect your gauge to or the dimming circuit in your vehicle does not dim the REDARC gauge to your liking. The GA-ELC also allows you to program nighttime brightness and colour of your REDARC gauges, including dimming if connected to a dash dimmer. Once programmed your gauges will change colour when turning on your park lights and back to a daylight colour when you turn them off. The GA-ELC is also 24 volt capable. Features: Satin Chrome Bezel 13 Selectable Backlight Colours Multiple programmable alert levels with amber or red backlight and audible beep Display illuminates when park lights are turned on so you can check battery voltages and discharge or charge current without turning on the ignition. If fitting more than one REDARC gauge, a communications link can be connected between the gauges to change the backlight colour of all at once. Specifications Warranty 2 Years Sensor(s) (Included) GS-P-150 Sensor (Optional) GS-UT-80 / GS-UT-120 / GS-OWT1-4 / GS-OWT1-8 Standby Current Draw 30mA Input (Operating) Voltage 6 - 16V Height (mm) 42 Weight (kg) 0.05 Videos

Redarc Single Voltage 52mm Gauge with Optional Current Display, 2-year warranty. The REDARC 52mm single voltage gauge is ideal for monitoring battery systems mounted in 4WD's, Campers, Caravans, Motorhomes and other similar vehicle applications. The LCD/ LED display allows you to monitor the charging performance of either your main or auxiliary battery. In the event of an alternator or system failure, the voltage reading on the gauge will be low and drop as the battery discharges. In the event of an overcharge condition, the voltage reading will climb above its normal zone. The G52-VA gauge also has pre-set alert levels (<9V and >16V) to notify you of these situations by changing the gauge backlight colour to either amber or red, and initiate an audible beep when the vehicle's ignition is on. Current Sensor The G52-VA gauge is also equipped with an optional 100A rated current display that monitors the amount of current to or from your main or auxiliary battery. This device can be fitted around the earth connection of the main or auxiliary battery. You will need to purchase the REDARC Hall effect current sensor (GS-AMPS) to equip the gauge with this function. When extra protection is required, the G52-VA is the perfect accessory for a REDARC dual battery isolator (SBI12) or in-vehicle battery charger (BCDC range) where a 12-volt battery is installed. It’s a visual monitor of product performance and battery health. The G52-VA gauge diameter requires a 52mm hole for mounting. REDARC offer a range of mounting solutions including a 2” black plastic mounting cup (GH-CUP) and one (GH-MP1), two (GH-MP2) and three (GH-MP3) hole gauge mounting panels. Radio inserts are also available that suit the Toyota Hilux (GH-RI05). The REDARC 24 to the 12-volt adaptor (GA-2412V) can be used to connect this gauge to a vehicle with a 24-volt ignition and lighting supply, however, only a 12-volt battery can be monitored. Enhanced Lighting Controller REDARC recommends the purchase of an Enhanced Lighting Controller (GA-ELC) with this gauge. The GA-ELC is designed to enhance the lighting of your REDARC gauges as only one required for a set. It is to be used when you do not have a dimming circuit to connect your gauge to or the dimming circuit in your vehicle does not dim the REDARC gauge to your liking. The GA-ELC also allows you to program nighttime brightness and colour of your REDARC gauges, including dimming if connected to a dash dimmer. Once programmed your gauges will change colour when turning on your park lights and back to a daylight colour when you turn them off. The GA-ELC is also 24 volt capable. The G52-VVA is also available as part of several Value Packs, offering a great saving on combined purchases. Features: Satin Chrome Bezel. 13 Selectable Backlight Colours. Multiple alert levels with amber or red backlight and audible beep - Alerts when Voltage drops below 9V or climbs above 16V. Display illuminates when park lights are turned on so you can check battery voltages and discharge or charge current without turning on the ignition. If fitting more than one REDARC gauge, a communications link can be connected between the gauges to change the backlight colour of all at once. Specifications Warranty 2 Years Sensor (Optional) GS-AMPS Standby Current Draw 30mA Input (Operating) Voltage 6 - 16V Height (mm) 42 Weight (kg) 0.05 Videos

Redarc EGT & Boost Pressure 52mm Gauge with Optional Temperature Display, 2-year warranty. The REDARC 52mm G52-BET gauge measures boost pressure and exhaust gas temperature. It also features an optional temperature display. The REDARC 52mm EGT & boost pressure gauge is a must for your diesel turbocharged vehicle. The G52-BEP is used to monitor the exhaust gas temperature (EGT) of turbo-equipped vehicles in conjunction with a pyrometer probe. EGT is an indication of how hot the combustion process is in a vehicle's cylinders. Excessive EGT can cause engine or turbocharger damage. Many conditions can result in excessive EGT (i.e. too much fuel or not enough air) and are made worse when a vehicle is pulling a heavy load, climbing or running at continuous high speeds. The boost pressure function monitors manifold air pressure and is used to ensure excessive pressure is not generated. By monitoring boost, you are able to keep the vehicle's engine components in the proper power range to achieve the most performance from your vehicle. The gauge is supplied with a “K” type EGT sensor and electronic boost MAP sensor interface. The boost has a peak hold function with a display range from 0- 35 PSI and a programmable alert level between 10 and 30 PSI. The EGT function also has a peak hold function with a range from 275 to 800 °C and is programmable between 500 and 800 °C. The EGT probe has a 1/8” NPT compression fitting and is supplied with a weld in the mounting bung. Temperature Sensor The G52-BET gauge also supports one of four optional temperature sensors. You will need to purchase one of the following REDARC temperature sensors to equip the gauge with this function: GS-UT-80: An NTC temperature sensor in a plastic housing for measuring cabin, fridge or outside temperature. Range is -20°C ~ + 80 °C. This sensor is supplied with a 6 metre extension cable. GS-UT-120: An NTC temperature sensor in a metal copper housing with 6mm diameter mounting hole. Range is -20~+120 °C. This sensor is supplied with a 6 metre extension cable. GS-OWT1-4: Water or Oil temperature sender. 1/4 NPT threaded. Designed to measure from -20~ +170°C. Supplied with 3 metre extension cable. GS-OWT1-8: Water or Oil temperature sender. 1/8 NPT threaded. Designed to measure from -20~ +170°C. Supplied with 3 metre extension cable. The G52-BET gauge diameter requires a 52mm hole for mounting. REDARC offer a range of mounting solutions including a 2” black plastic mounting cup (GH-CUP) and one (GH-MP1), two (GH-MP2) and three (GH-MP3) hole gauge mounting panels. Radio inserts are also available that suit the Toyota Hilux (GH-RI05). 2.5” (GMC-2.5) and 3.25” (GMC-3.25) muffler clamps are also available from REDARC to hold the EGT probe. The REDARC 24 to 12-volt adaptor (GA-2412V) can be used to connect this gauge to a vehicle with a 24-volt ignition and lighting supply. Enhanced Lighting Controller REDARC recommends the purchase of an Enhanced Lighting Controller (GA-ELC) with this gauge. The GA-ELC is designed to enhance the lighting of your REDARC gauges as only one required for a set. It is to be used when you do not have a dimming circuit to connect your gauge to or the dimming circuit in your vehicle does not dim the REDARC gauge to your liking. The GA-ELC also allows you to program nighttime brightness and colour of your REDARC gauges, including dimming if connected to a dash dimmer. Once programmed your gauges will change colour when turning on your park lights and back to a daylight colour when you turn them off. The GA-ELC is also 24 volt capable. Included: 52mm gauge with wiring harnesses for power/programming and connection to sensor interface. MAP Sensor interface box. Diesel EGT pyrometer probe with 1/8” NPT compression fitting and 96” lead wire. 1.8m Hose with T-Piece to tap into vehicle’s manifold boost/vac hose. K-Type thermo coupler. Weld in mounting bung. Mounting bracket with fasteners and P-Clip. Features: Satin Chrome Bezel. 13 Selectable Backlight Colours. EGT and boost peak hold functions. Multiple programmable alert levels with amber or red backlight and audible beep. Display illuminates when park lights are turned on so you can check battery voltages and discharge or charge current without turning on the ignition. If fitting more than one REDARC gauge, a communications link can be connected between the gauges to change the backlight colour of all at once. Specifications Warranty 2 Years Sensor(s) (Included) Boost EGT Interface Sensor (Optional) GS-UT-80 / GS-UT-120 / GS-OWT1-4 / GS-OWT1-8 Standby Current Draw 30mA Input (Operating) Voltage 6 - 16V Height (mm) 42 Weight (kg) 0.05 Videos

Redarc Oil Pressure & Water Temperature 52mm Gauge With Optional Temperature Display, 2-year warranty. The REDARC 52mm single oil pressure & water temperature gauge is ideal for monitoring your engines oil pressure and coolant temperature. The G52-PWT gauge is supplied with one REDARC oil pressure sensor that displays from 0 to 80 PSI and a REDARC 1/8 NPT thread water temperature sensor that displays from 30 to 120 degrees Celsius. Monitoring oil pressure ensures the longevity of your vehicle and allows you to ensure that the correct pressure is maintained so that your car bearings are well lubricated. This is crucial when travelling at continuous high speeds and towing heavy loads. Low oil pressure can be an indicator of a low oil level, diluted or worn out oil, worn engine bearings, high oil temperature or a worn oil pump. Temperature Sensor  The G52-PWT gauge also supports one of four optional temperature sensors. You will need to purchase one of the following REDARC temperature sensors to equip the gauge with this function: GS-UT-80: An NTC temperature sensor in a plastic housing for measuring cabin, fridge or outside temperature. Range is -20~+80°C. This sensor is supplied with a 6 metre extension cable. GS-UT-120: An NTC temperature sensor in a metal copper housing with 6mm diameter mounting hole. Range is -20~+120°C. This sensor is supplied with a 6 metre extension cable. GS-OWT1-4: Water or Oil temperature sender. 1/4 NPT threaded. Designed to measure from -20~ +170°C. Supplied with 3 metre extension cable. GS-OWT1-8: Water or Oil temperature sender. 1/8 NPT threaded. Designed to measure from -20~ +170°C. Supplied with 3 metre extension cable. The G52-PWT gauge diameter requires a 52mm hole for mounting. REDARC offer a range of mounting solutions including a 2” black plastic mounting cup (GH-CUP) and one (GH-MP1), two (GH-MP2) and three (GH-MP3) hole gauge mounting panels. Radio inserts are also available that suit the Toyota Hilux (GH-RI05). The REDARC 24 to the 12-volt adaptor (GA-2412V) can be used to connect this gauge to a vehicle with a 24-volt ignition and lighting supply, however, only a 12-volt battery can be monitored. Enhanced Lighting Controller  REDARC recommends the purchase of an Enhanced Lighting Controller (GA-ELC) with this gauge. The GA-ELC is designed to enhance the lighting of your REDARC gauges as only one required for a set. It is to be used when you do not have a dimming circuit to connect your gauge to or the dimming circuit in your vehicle does not dim the REDARC gauge to your liking. The GA-ELC also allows you to program nighttime brightness and colour of your REDARC gauges, including dimming if connected to a dash dimmer. Once programmed your gauges will change colour when turning on your park lights and back to a daylight colour when you turn them off. The GA-ELC is also 24 volt capable. Features: Satin Chrome Bezel. 13 Selectable Backlight Colours. Multiple programmable alert levels with amber or red backlight and audible beep. Display illuminates when park lights are turned on so you can check battery voltages and discharge or charge current without turning on the ignition. If fitting more than one REDARC gauge, a communications link can be connected between the gauges to change the backlight colour of all at once. Specifications Warranty 2 Years Sensor(s) (Included) GS-P-150, GS-OWT1-8 Sensor (Optional) GS-UT-80 / GS-UT-120 / GS-OWT1-4 / GS-OWT1-8 Standby Current Draw 30mA Input (Operating) Voltage 6 - 16V Height (mm) 42 Weight (kg) 0.05 Videos