Electric Brake Controllers (7)

Redarc Universal Tow-Pro Wiring Kit, 2-Year Warranty. The REDARC TPWKIT-013 Universal Tow-Pro Wiring Kit supports the installation of the Tow-Pro Elite electric trailer brake controller into a wide range of vehicles. It is suitable for vehicles where the start battery, Tow-Pro main unit, and the cable run to the cabin are all in-line, via a 1.8m power cable length. The Universal Tow-Pro Wiring Kit range replaces the Tow-Pro Wiring Kit range and consolidates the range from 10 kits down to 3. The Universal Tow-Pro Wiring Kit comes with the complete range of hardware required to install a Tow-Pro Elite brake controller and contains a Wago Boot, Protection Device, Wiring Harness, Mounting Bracket, and fitting instructions. REDARC’s new Universal range of Wiring Kits feature technology that enables compatibility with modern driver aids such as Autonomous Emergency Braking, Adaptive Cruise Control, lane departure, collision avoidance, and where the vehicle brake signal may be generated from different systems. By using a REDARC Tow-Pro Wiring Kit you ensure the quick and high-quality installation of Australia’s favourite brake controller, the Tow-Pro Elite. REDARC offers a wide range of accessories to aid and assist the install of the market-leading Tow-Pro Elite into most vehicles including Switch Inserts, Remote Head Wiring Kits, Encapsulated Protection Devices, and a Mounting Bracket Kit. Redarc has created this Universal Tow-Pro kit to replace the old TPWKIT-002, TPWKIT-004, TPWKIT-006, TPWKIT-007 and TPWKIT-009 kits    

Redarc Hand Brake Alarm Continuous Tone 12 or 24V with a 2-year warranty The HBA1224 alarm is used in a 12V or 24V automotive system. It monitors the handbrake switch and the doorframe switch* to provide audible and visual warning if the door is opened while the handbrake is not applied. Once the alarm starts, it stays latched on until the handbrake is applied (even if the door is closed again). The HBA1224 improves vehicle safety as it: Reduces the risk of the vehicle being accidentally left unattended without the handbrake on. If used with an external relay/horn, it can provide a warning to anyone in the general area, that a vehicle has been left without its handbrake on. Hummingbird Electronics offers an optional external “Compact Combination Warning LED and Buzzer” which is perfectly suited for REDARC’s Hand Brake Alarm.  Available in both 12 and 24-volt variants.  Benefits Warns you when you forget to apply the handbrake Security against damage caused by runaway vehicles Horn output ensures others will be warned A mandatory health and safety installation on many mining site vehicles  Features Suitable for all vehicles Built-in LED warning light and internal piezo buzzer plus external output Designed for universal fitment Output latches on once triggered Can be used in various other installations (headlight alarm) *The doorframe switch is the switch mounted in the doorframe that switches on the cab light when the door is opened. Specifications Warranty 2 Years Standby Current Draw <2mA Input (Operating) Voltage 9 - 32VDC Length (mm) 50 Width (mm) 30 Height (mm) 25 Weight (kg) 0.04

Redarc Trailer Brake Controller 12v 1 - 3 Axles with 2 years warranty. The REDARC range of electric trailer brake controllers provides an easy to operate method of controlling electric brakes on a trailer, camper-trailer, boat trailer or caravan. Your trailer behaves exactly as you expect it to whenever you apply the vehicle brakes. What’s more, you can apply the trailer brakes independently of the towing vehicle’s brakes, giving you absolute control over your trailer - no more uncontrollable sway! The LED indicator on the 12V trailer brake controller or dashboard panel (depending on installation type) glows green when a trailer with electric brakes is plugged in. Application of the brakes from the foot brake or the manual button on the controller will change the LED to red - the shade of red indicating to what degree the brakes are being applied. The adjustment knob will set the level of braking whether activated by the manual button or the foot brake. Benefits Ensures safe braking when towing a trailer The remote head model means no more hitting your knees on your brake controller The remote head model allows for a neat installation The trailer mount model allows towing from multiple tow vehicles Simple to operate and easy to install Features Compact size LED status and braking force indication Override button for independent trailer brake activation Simple gain adjust for variation in braking force It May be installed at any angle without affecting performance Specifications Input (Operating) Voltage 12VDC Input Fuse Rating 30A (Cicruit Breaker) Warranty 2 Years Protection Reverse Polarity, Short Circuit Weight (kg) 0.2 Output System Voltage 12VDC Output Current Rating (Cont.) 18A Length (mm) 100 Width (mm) 50 Height (mm) 30

Redarc Break-Away Controller Remote Monitor, 2 year warranty. The RM6000 remote monitor provides the only accurate way to monitor the breakaway battery condition, and will give an audible and visual signal if the battery condition falls below the acceptable levels (using a volt meter to monitor the Break-Safe battery is dangerous, as it will not give a true indication of the battery condition). The new RM6000 remote monitor operates each time the brake pedal in the tow vehicle is pressed. Specifications Input (Operating) Voltage 12VDC Length (mm) 80 Width (mm) 59 Height (mm) 29 Warranty 2 Years Weight (kg) 0.1

Redarc Break-Away Controller Device, 2-year warranty. The REDARC Brake-Safe Break-Away system for 2 or 4 wheel trailer brakes is designed to apply the brakes and brake lights on a trailer or caravan should it accidentally separate from the tow vehicle. The system has a built-in battery that can be charged from the tow vehicle's auxiliary line or by a battery charger. The easy to operate test button is used to indicate the level of charge in the battery. This should be checked before the trailer is towed. Specifications Input (Operating) Voltage 12VDC Warranty 2 Years Length (mm) 170 Width (mm) 160 Height (mm) 90 Weight (kg) 3.6

Redarc Tow Pro Classic Electric Brake Controller, 2 year warranty. The Tow-Pro range of Electric Brake Controllers sets the benchmark for easy-to-use, safe braking on trailers, camper trailers, boat trailers. Now there’s a REDARC Tow-Pro to suit every towing need and budget! The Tow-Pro Classic Electric Brake Controller is the next generation Electric Brake Remote Head (EBRH), now with the extra performance and reliability of the Tow-Pro platform. It incorporates quality and performance improvements whilst retaining the EBRH look and feel. Suitable for 12 volt systems, Tow-Pro Classic Electric Brake Controller is simple to install and operate and offers a single (user-controlled) mode of braking at the turn of a dial with braking force LED indication. The Tow-Pro Classic brake controller is able to operate both electric and electric/hydraulic trailer brakes without manual selection and is AL-KO ESC and Dexter Sway Control System compliant. User-Controlled Mode Tow-Pro Classic offers a user-controlled mode of braking allowing the driver complete control of the brake level whether the footbrake or override is applied. The trailer will behave exactly as expected whenever the vehicle brakes are applied and works independently of the vehicle’s brakes. Adjusting the control knob in user-controlled mode will adjust the braking force from minimal (0) to maximum (10). Benefits Smooth trailer braking response User controlled-mode braking AL-KO ESC and Dexter Sway Control System compliant Electric/hydraulic operation Features Suitable for 12-volt vehicle systems Compact size   Short Description Redarc Tow Pro Classic Electric Brake Controller, 2 Year Warranty SKU EBRHV2 Brands Redarc Product Category Electrical Accessories Standby Current <10mA Output System Voltage 12VDC Dimensions (WxHxL mm) 100mm x 30mm x 85mm Output Current Rating 25A Input Fuse Rating 30A (Circuit Breaker) Input Voltage 9 - 16VDC Net Weight (kg) 0.2 Kg Manufacturers Warranty 2 Years

Redarc Tow-Pro Elite Electric Brake Controller Version 3, 2 year warranty Redarc have upgraded the firmware in the new Version 3. The Tow-Pro Elite is an electric brake controller designed to suit most common trailer braking applications whilst requiring minimal dash space and is simple to install and operate. The Tow-Pro™ Elite trailer brake controller offers selectable Automatic or User Controlled trailer braking modes allowing the user to choose the braking style depending on the road or terrain conditions, vehicle type, or driver preference. The Tow-Pro™ Elite electric trailer brake controller features Active Calibration which constantly monitors the direction of travel, the unit will even calibrate with no trailer attached whilst maintaining the ability to mount in any orientation. The unit is able to operate both electric and electric/hydraulic trailer brakes, and will operate from either 12V or 24V. The vehicle systems without the need for manual selection or extra components or wiring. The unit is also Australian Design Rules (ADR) compliant when installed as directed. NOTE: Important information when fitting Towpro V3 to the newer Ranger and basically every 2018+ vehicle. With the Ford Ranger PX3 variant, it is essential that you use a TPWKIT-012 It is advised to use the specific TPWKIT-xxx harness as it includes a protection device (diode). Please see accessories for further Wiring Kits. Alternatively, if you want to build your own harness, make sure you use the EPDK-001, to not back feed the trailer lighting module. Please see the accessories for the protection device. SPECIFICATIONS   Input (Operating) Voltage 9 - 32VDC Input Fuse Rating 30A (Circuit Breaker) Standby Current Draw <10mA Output System Voltage 12VDC Output Current Rating (Cont.) 25A Length (mm) 85 Width (mm) 100 Height (mm) 30 Weight (kg) 0.2 Warranty 2 Years